VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit leak test pre-order guide guide
starter vape kits · convenience store chains

Starter Vape Kit leak test pre-order guide guide

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for convenience store chains.

Published 17 June 2025  ·  VapeWholesaleHub  ·  Reading time 9 min

Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.
Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Starter Vape Kit leak test pre-order guide guide configuration from a production run, photographed before packing.
Starter Vape Kit leak test pre-order guide guide configuration from a production run, photographed before packing.

Assortment planning without the guesswork

Starter Vape Kit is a specification decision before it is a price decision. Get the resistance, the capacity and the packaging right and the price conversation becomes short. Get them wrong and no discount will rescue the order.

Most convenience store chains arrive with a spreadsheet and leave with too many SKUs. The fix is not a bigger catalogue, it is a narrower core. We normally propose three tiers: a volume line that carries the shelf, a step-up line that lifts basket value, and one trial SKU that tells you what to order next season.

The first question we ask is not what you want to spend. It is what your customer already buys. Answer that and the starter vape kit list writes itself; skip it and you end up with a pallet of stock that photographs well and sells badly.

Quality control, in plain terms

Flavour drift between batches is the quiet killer of repeat orders. We retain a sealed reference sample from every run so a complaint six weeks later can be compared against what actually left the building.

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

For convenience store chains, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Shipping without surprises

We ship from Shenzhen and Guangzhou: air express for samples and part loads, sea freight for volume. Typical production lead time is 28 working days after artwork approval, plus transit. We quote both routes so you can see the trade-off instead of guessing at it.

For repeat buyers we hold a shipping schedule rather than shipping on request. A fixed weekly cut-off means your reorder lands before the shelf empties instead of after.

  • Standing reorder schedule with a fixed cut-off
  • Batch codes traceable from carton back to production date
  • Private label files archived for future rebrands
  • Consolidated or split shipping, quoted both ways
  • Document pack prepared per destination market
  • Named account contact who has handled the product

Getting the documents right

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

Advertising rules are stricter than product rules in most markets. Claims about cessation, health or comparative performance should stay off packaging and off your product pages unless your legal team has signed them off.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity2.5 ml
Coil resistance1.0 ohm
IncludedDevice, 2 pods, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order100 units per SKU, mixed cartons allowed
Lead time18 working days after artwork approval

The detail above is what we hold ourselves to on every shipment, including the small ones. It is also the list we will walk through with you before the first order.

Frequently asked

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

What is the minimum order for starter vape kit?

Standard configurations start at 200 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 500 units because of setup time on the line.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us